Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

Hexapod多自由度微激励系统的振动时域波形控制

摘要： Hexapod多自由度微激励系统常用于航天器有效载荷在轨微振动环境的模拟，但采用现有控制方法无法精确稳定跟踪低频正弦加速度，这是由于系统耦合度高、非线性在低频段较强，被控对象相位滞后过大造成的.针对此问题，基于传统离线迭代控制方法，提出一种复合超前校正、多倍频陷波滤波器的改进离线迭代控制方法.其中，离线迭代进行补偿控制，超前校正进一步补偿系统相位，多倍频陷波滤波器去除非线性干扰.跟踪低频定频正弦加速度的实验结果表明，对比传统离线迭代控制方法，改进方法收敛快、控制精度高；对比现有自适应正弦振动控制方法，改进方法将符合精度要求的加速度控制频带下限由14.5 Hz扩宽至8 Hz.实验结果验证了所提方法的有效性.     

PWM低速爬行状态系统波动分析

脉宽调制技术（PWM）在自动控制领域有着广泛的应用。然而，在实际工程应用的过程中，包含PWM的系统在低速驱动的条件下难以达到高精度速度指标的要求。在工程实践经验的基础上，对这一问题进行详细分析，提出PWM的截断效应和移频效应引起波动的理论，并结合典型的机电伺服系统模型进行仿真，完成仿真层面的验证。仿真结果展示了机电伺服系统在低转速状态下由于PWM的截断效应引起转速波动的现象，契合了实际系统中表现的情况，验证了截断效应和移频效应的正确性，为提高系统精度指标提供了依据。     

面向空间天线的TWF复合材料性能研究

利用碳纤维三向编织物（triaxial woven fabric，TWF）作为增强材料，与柔性基体材料硅橡胶复合，制成兼具一定柔性和刚性的复合材料壳膜结构，用于卫星天线反射器，是一种新型的高精度可展开天线实现方案。采用复合材料细观方法，对碳纤维增强硅橡胶TWF复合材料进行了力学性能的研究。首先由纤维和基体的材料特性得到均质纤维束的材料特性；接下来考虑纤维束交织情况（起伏波动）建立由纤维束组成的单胞实体有限元模型；然后对单胞实体有限元模型进行均匀化分析，施加周期性边界条件，最终得到等效的均质材料特性；为满足天线反射器高性能需求，分析了碳纤维种类、纤维体积分数对单胞等效性能的影响规律。对该材料力学性能的研究，可以为其未来应用于大型高精度可展开天线反射器提供一定的理论依据。     

航空航天制造机器人高精度作业装备与技术综述

新一代航空航天产品的研制与批产对制造精度与加工质量提出了更高的新要求。以机器人为核心的智能制造技术与装备是解决该难题的有效途径。然而,工业机器人较低的定位精度与弱刚性结构属性严重制约了其在航空航天部件高精度加工作业中的推广应用。本文在阐述国内外机器人装备在航空航天制造业的应用现状的基础上,重点介绍了机器人作业刚度强化策略与定位误差精确补偿方法的研究现状,并分析了现有高精度控制方法存在的问题及技术难点。最后探讨了机器人作业装备在航空航天制造领域的技术发展趋势,为面向航空航天产品的机器人高精度制造技术的研究提供参考与借鉴。     

四相横向磁通永磁电机的三电平滞环电流控制

以新型四相横向磁通永磁电机为研究对象,利用MATLAB/Simulink软件平台以及Simpower System工具箱,对闭环控制系统进行了研究。在传统双闭环调速控制基础上,为滞环电流控制环引入零电平,将滞环分为上滞环和下滞环。综合考虑开关频率与电流THD确定合适的滞环环宽,并根据偏差电流值与滞环环宽比较值得到逆变器控制信号。通过仿真得到各种工况下的电机运行数据,说明该控制方法能够对四相横向磁通永磁电机进行有效控制。     

薄壁微三维结构件超精密研抛技术研究

针对影响薄壁微结构件超精密研抛的工艺因素,即单次进给量、研磨轨迹、研磨膏选择和去除量精确控制,通过大量的研抛加工试验,进行研抛工艺研究,得到能实现稳定和理想加工结果的研抛工艺,很好的满足零件性能要求。     

预旋系统稳态和非稳态计算对比研究

针对预旋系统由于旋转引起流场和温度场参数周期性瞬态变化的问题，分别采用滑移网格的瞬态法和固定转子相位的稳态法进行数值求解，并在稳态计算中通过改变转子相位来近似模拟非稳态问题的时空变化特性。通过稳态空间平均结果与非稳态时均结果的对比，以期为预旋系统非稳态问题的低成本求解提供方法依据。结果表明：稳态计算结果与非稳态计算结果相比，周期性波动频率一致，接受孔进口处，稳态计算的压力波动幅度小39%左右，温度波动幅度小15%左右；多个相位的稳态空间平均结果与非稳态时均结果相比，压力高0.2%，温度低0.1%；采用多个计算周期数与单个周期的非稳态计算结果差异微小。当采用喷嘴出口气流中心正对接受孔迎风面前缘的转子相位时，稳态计算结果与非稳态计算时均结果最接近。     

Carrier phase prediction method for GNSS precise positioning in challenging environment

Since the signals of global navigation satellite system (GNSS) are blocked frequently in challenging environments, the discontinuous carrier phases seriously affect the application of GNSS precise positioning. To improve the carrier phase continuity, this paper proposes a carrier phase prediction method based on carrier open-loop tracking. In the open-loop tracking mode, the carrier numerically controlled oscillator (NCO) is controlled by the predicted Doppler, but not by the loop filter output. To improve the phase prediction effective time, accurate receiver clock drift estimation is studied in the prediction method. The phase prediction performance is tested on GNSS software receiver. In the phase prediction effective time tests, open-loop processes were set for the tested channel. The test results show that, when some satellite signals are blocked in 15?s, the probability of carrier phase error less than quarter cycles is more than 94%. In the real time kinematic (RTK) positioning tests, some satellite signals are blocked in 10–15?s repeatedly. The test results show that, the carrier phase continuity is basically not affected by the signal interruption, and the RTK can almost keep continuous centimeter-level positioning accuracy without re-fixing the integer ambiguity.